Partners Blog Contacts

Below are some recommended starting threshold values for the Vidyo MIB Traps.

Each includes examples of how to set each using the snmpset command:

Portal:
LINES LICENSE THRESHOLD PERCENTAGE

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.2.3.20.0 INSTALL LICENSE THRESHOLD PERCENTAGE

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.2.3.21.0 Default values are 80 (for 80%)

Router:
CASCADE MEDIA ALERT ENABLE/DISABLE

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.1.3.30.0

(set to 2 to disable) Cascade Media traps are already enabled by default.

CASCADE MEDIA JITTER THRESHOLD

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.1.3.31.0 (100000 for over internet) Default value is 10000. Value is in microseconds,

CASCADE MEDIA LOSS THRESHOLD PERCENTAGE

u 80 u 80

u 1

u 30000
so 30000 is 30ms of jitter.

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.1.3.32.0
(500 for over internet) Default value is 100. Value is in hundredths of a percent, so 300 is 3% packet loss.

PARTICIPANT MEDIA ALERT DISABLE/ENABLE

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.1.3.35.0 u 2

PARTICIPANT MEDIA JITTER THRESHOLD

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.1.3.36.0 u 30000
(100000 for over internet) Default value is 10000. Value is in microseconds, so 30000 is 30ms of jitter.

PARTICIPANT MEDIA LOSS THRESHOLD PERCENTAGE

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.1.3.37.0 u 300
(500 or even 1000 for over internet) Default value is 100. Value is in hundredths of a percent, so 300 is 3% packet loss.

Gateway:

Gateway trap thresholds are set to high value by default, effectively disabling them.
Recommend starting off with the SNMP thresholds below on the Gateway and tweak as necessary. These will trigger every minute if jitter hits 50 ms or more than 5 percent packet loss.

FREQUENCY CHECK

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.3.1.3.5.0 u 60 JITTER THRESHOLD

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.3.1.3.6.0 u 50

PACKET LOSS THRESHOLD PERCENTAGE

snmpset -v 2c -c rw_community host_address 1.3.6.1.4.1.35969.1.1.3.1.3.7.0 u 5

u 300

(1 to enable) Participant Media traps are disabled by default and it is typically recommended to leave disabled unless needing to

troubleshoot/monitor for brief time specifically, as these can be very chatty specially where mobile clients may be in use, etc.

Was this article helpful?
0 out of 0 found this helpful

0 Comments

Follow
Please sign in to leave a comment.